U.S. Cooler Saves Customers Money with Energy Efficient Walk-ins

Most walk-in coolers and freezers are purchased based upon the initial cost. What many fail to realize is that operational costs can dig deep into consumers’ pockets. U.S. Cooler is giving the Cold Storage Industry an energy efficient option by manufacturing walk-ins with extruded polystyrene insulation.

Extruded polystyrene is the most efficient insulation available on the market. Over time, extruded polystyrene resists moisture while other insulations start absorbing it. One must consider a real life application to understand moisture absorption.

Freezers normally operate at -10° F inside, but may have an exterior temperature of up to 95° F or even more. With the extreme difference in temperatures, the insulation is vulnerable to retaining moisture in the structural voids. When water starts collecting inside walk-in insulation, the R-value drops and moisture inside the insulation starts to freeze.

When moisture is absorbed and R-values start to decrease, refrigeration systems start working harder and longer to make up for the heat transferring into the walk-in. A refrigeration system working overtime means higher energy bills. By using extruded polystyrene, consumers can save that money.

Extruded polystyrene is unique; the insulation is a closed-cell product, meaning the cells of the material are so tightly packed together that moisture has a difficult time penetrating, which is optimal for moisture resistance and keeps the R-value from decreasing.

Using studies performed by the U.S. Army Corps of Engineers (CREEL), U.S. Cooler demonstrated extruded polystyrene saved consumers over $5,000 in energy costs over the first five years of operation. The savings again are due to extruded polystyrene’s ability to resist moisture and to retain its R-value better than other insulators.

When buying and selling walk-ins, consider more than the initial cost of the walk-in-consider energy costs. Educate yourself about how to save money; to find out more about extruded polystyrene and energy savings, call 800.521.2665 or visit www.uscooler.com.

California Accepts EISA Regulations

The use of energy has become a commonly discussed issue with environmental and economic concerns. Everyday a significant amount of energy is used for commercial equipment in restaurants, grocery stores, convenience stores, and warehouses. Prior to 2006, there had not been any set regulations on energy usage for commercial refrigeration.

California was one of the first states to set energy regulations for walk-in coolers and freezers. They previously required an envelope insulation rating of R-28 for refrigerators and R-36 for freezers. California was also one of the first to require electronically commutated motors or permanent split capacitor-type motors for refrigeration. Before more states could pose their own requirements on energy consumption, the federal EISA (Energy Independence and Security Act) agreement was signed in 2007. California has fully accepted the EISA requirements, amending their previous appliance energy code.

To review the entire California Code of Regulations, click on the link below. The walk-in cooler and freezer section starts on page 120 of the document.

http://www.energy.ca.gov/2008publications/CEC-400-2008-021/CEC-400-2008-021-15DAY.PDF

Cooler Insulation- Extruded Polystyrene Vs. Polyurethane

U.S. Cooler manufactures walk-in coolers and freezers employing both Polyurethane and Extruded Polystyrene. Through testing and years of experience we maintain that extruded polystyrene insulation is superior for use in walk-in coolers and freezers. Polystyrene has many characteristics that prove it to be the best insulation material for walk-ins. The two main insulations found in walk-ins are Extruded Polystyrene and Polyurethane. Each insulation has differentiating characteristics and should be optimized for the specific application.

Polystyrene is a dense closed-cell structure that is very resistant to moisture and holds its R-Value longer than other competing insulations found in walk-ins, such as Polyurethane. This allows less water infiltration in the insulation, which in turn saves energy and money. When water starts seeping into the insulation’s pores, the R-value drops dramatically causing the refrigeration to work harder to hold its respective temperature. Refrigeration working overtime means higher energy bills. Polystyrene is less water vapor permeable; therefore, water vapor does not infiltrate through the material as quickly or easily as it does other insulations.Using studies performed by the U.S. Army Corps of Engineers (CRREL), U.S. Cooler demonstrated extruded polystyrene saved consumers over $5,000 in energy costs over the first five years of operation. The savings again are due to extruded polystyrene’s ability to resist moisture and to retain its R-value better than other insulators.

Polystyrene used in walk-in coolers and freezers is made from “at least 20% pre-consumer recycled polystyrene.” (Owens Corning, Technical Bulletin: Recycle Content Claims Must be Reliable and Verifiable) Polystyrene found in walk-ins is also 100% recyclable. Manufacturing companies that produce these insulation materials, reproduce the resources in new insulation material. Alternatively, it is important to note that Polyurethane is produced from chemicals and is not made from any recycled materials nor can it be recycled or reused.

Polystyrene in walk-in coolers and freezers is the most cost effective and environmentally friendly insulation used in walk-ins today. Not only is polystyrene in walk-ins made with recycled materials and is 100% recyclable but it is energy efficient and can save a great deal of money in energy costs and reduce carbon footprint over the life-cycle of the walk-in.

Interesting debate

This is a link to a debate on which insulation is better (extruded polystyrene or polyurethane) on the HVAC-Talk forums. Several of the posts mention U.S. Cooler.